Sony DLP Lamp XL-100 How-To Replacement Guide

[Español]

You will be redirected to the new guide in  seconds

For Part Number: Sony DLP Lamp XL-100U, XL-100E, XL-100J, XL-100C, XL100U, XL100E, XL100J, XL100C, A1501247A, A-1501-247A, A-1501-247-A, A1501-247A, 386182611, A1501247A.

( Sealed replacement lamp for televisions, BIG with no vents ).

For Enclosure: Sony Lamp ( XL-100 / 4-051-342 ).

Television Type: LCD.

For Bulb: UHP 100W 1.3

Lamp Philips P23 UHP 100W 1.3

P 23 1.3 Philips.

Click below to buy this lamp now:
buy now
Lowest Prices Anywhere!

Compatible TV Models: KL-W7000, KL-W9000, KL-X9200M, KL-X9200U, KL-W7000A, KL-W9000A.

Assembly part numbers: 2001294, 4-051-345, 1-517-07-16, 101437416.

NORMAL DISCLAIMER:
— Do NOT purchase generic brand lamps such as LTI, APO or third-party manufacturers such as OSRAM.

These lamps were NOT engineered with and for your TV…only your Philips lamp has been engineered to work flawlessly and output the best possible color. Above that, it just doesn’t make sense to choose an aftermarket lamp for a $5-$10 difference (and in many cases they are more expensive!!). Be a smart consumer and do your research! Discount-Merchant.com promises to be the low price leader in all Projection TV Lamps they carry…if this is not true, let us know and we’ll fix it!

Tools Required: Standard Philips & Flathead screwdriver, Pair of Pliers, A new lamp.

Time Required: About 15 minutes.

Abstract: This guide is being published to show how easy it is to replace your original Sony XL-100 Lamp.

NOTE: The bulb should be handled with a clean lint-free cloth at all times to avoid any dirt or oil. Our hands are naturally oily…The oil residue from our hands can cause premature failure of the lamp if the front side of the lamp is not wiped down after the installation. It doesn’t hurt to do a final wipe with a clean, non-abrasive, lint-free cloth before reinstalling your lamp…

 

Sony XL-100

Sony XL-100 Lamp casing

 
Metal cage 2001294

1.-Let’s start by removing the screws on the bottom of the enclosure.

.

Metal cage 2001294 & Lamp enclosure 4-051-342 & lamp enclosure 4-051-342

2.-Now place it on its side to find the power connector, and just below it you’ll find two small securing clips.

 
Metal cage 2001294 & Lamp enclosure 4-051-342 & lamp enclosure 4-051-342

3.-To remove the metal cage you’ll have to insert a Flathead screwdriver between it and the plastic enclosure.

Metal cage 2001294

4.-Now, gently pull the metal cage out and tug it, just a bit until its sets free.

 
Philips Lamp P23 UHP 100 w 1.3, Twin plastic coverd cables & metal wire

5.-In the inter lamp, two plastic covered cables attached to the bulb by a nut and a screw, remove them.

Philips Lamp P23 UHP 100 w 1.3

6.-There is a metal wire holding the lamp in place, and it has a small plastic hook as a safety, be careful and pull it back.

 
Lamp enclosure 4-051-342 & lamp enclosure 4-051-342

7.-After the wire has been completely pulled back the bulb will be free.

Metal plate part No. NA71982

8.-The enclosure without the bulb will look something like this.

 
Philips Lamp P23 UHP 100 w 1.3

9.-Ready your new Philips brand lamp that should look like this.

Philips Lamp P23 UHP 100 w 1.3

10.-Place it in the same way you removed the old one.

 
Philips Lamp P23 UHP 100 w 1.3, Twin plastic coverd cables & metal wire

A.-After inserting the bulb, pull over the wire to connect the two plastic cables to the lamp.

Philips Lamp P23 UHP 100 w 1.3, Twin plastic coverd cables & metal wire

B.-Use your screw driver and pliers to secure the cables. 

 
Philips Lamp P23 UHP 100 w 1.3 & metal wire

C.-Remember that the wire goes into the hook on the back.

Metal cage 2001294

D.-Grab your metal cage and insert it back on to the enclosure

 

 
Metal cage 2001294 & Lamp enclosure 4-051-342 & lamp enclosure 4-051-342

E.-Remember to make sure that the two metal safety’s snap, that will mean that the cage is secure to the enclosure.

Metal cage 2001294 & Lamp enclosure 4-051-342 & lamp enclosure 4-051-342

F.-Insert back the screw on the side of the lamp and make sure that the metal cage doesn’t move.

 

 
Sony XL-100

G.-And finally you’re finished.

 

IMPORTANT: After installing the replacement bulb, you should wipe it with a clean cloth to avoid any dirt or oil. Our hands are naturally oily…this could reduce considerably the life span of the new lamp.

Again, Discount-Merchant.com promises to be the low price leader in all Projection TV Lamps they carry…if this is not true, let us know and we’ll fix it!

Click below to buy this lamp now:
buynow
Lowest Prices Anywhere!

 

FixYourDLP.com Blog | FixYourDLP.com Forum | Guides
FixYourDLP Flickr | FixYourDLP YouTube

Copyright ©2014 FixYourDLP.com. All content on this website is intended for information purposes only. FixYourDLP.com is not responsible, nor liable for any damage caused by the end-user, faulty lamps or parts. Please, always have a service center or a trained service technician advise you before beginning any repairs on your own.