[Español]
For Part Number: UX21516, UX-21516, UX21516RL (Sealed replacement lamp for DLP televisions, small lamp with no vents)
For Enclosure: Hitachi Lamp (enclosures UX21516 / LP700).
Lamp Type: LCD.
For Bulb: UHP 100w / 120w 1.0
Philips P22 100W/120W 1.0
Click below to buy this lamp now:
Lowest Prices Anywhere!
Compatible TV Models: 50VF820, 50VG825, 50VS810A, 55VF820, 55VG825, 60VF820, 60VG825, 60VS810A.
Assembly part numbers: NA63991, NA72182, NT0455, NA63941.
NORMAL DISCLAIMER:
— Do NOT purchase generic brand lamps such as LTI, APO or third-party manufacturers such as OSRAM.
These lamps were NOT engineered with and for your TV…only your Philips lamp has been engineered to work flawlessly and output the best possible color. Above that, it just doesn’t make sense to choose an aftermarket lamp for a $5-$10 difference (and in many cases they are more expensive!!). Be a smart consumer and do your research! Discount-Merchant.com promises to be the low price leader in all Projection TV Lamps they carry…if this is not true, let us know and we’ll fix it!
Tools Required: Standard Philips or Flathead screwdrivers, Pair of Pliers, A new lamp.
Time Required: About 15 minutes
Abstract: This guide is being published to show how easy it is to replace your original Hitachi Lamp UX21516.
NOTE: We recommend you to use latex gloves when handling the new bulb, to avoid any dirt or oil. Our hands are naturally oily…The oil residue from our hands can cause premature failure of the lamp if the front side of the lamp is not wiped down after the installation. It doesn’t hurt to do a final wipe with a clean, non-abrasive, lint-free cloth before reinstalling your lamp…
|
1.-Hitachi DLP Lamp UX21516 |
|
|
2.-Let’s remove the metal case by unscrewing it from the plastic housing. |
|
3.-Take the screwdriver to remove the top plastic piece. |
|
|
4.-Now, gently remove the metal casing from the plastic one. |
|
5.-Now remove the screws holding the lamp in place. |
|
|
6.-Also remove the screw on the side of the case holding the cables. |
|
7.-Cautiously give it a pull to remove the small metal case. |
|
|
8.-Now, carefully remove the cable that’s connected to the lamp. |
|
9.-Now take the bulb out by turning it slowly to the side and leaning it just a bit. |
|
|
10.-Disconnect both cables attached to the lamp. |
|
11.-Start reconnecting the two plastic covered cables to the lamp and place the metal ring over the top. |
|
|
12.-Your new lamp should look like this, so get ready to install it the same way you took out the other one. |
|
13.-And the lamp should be able to move a bit. |
|
|
14.-Place back the metal ring, to insert the bulb back in its casing rotate the bulb while leaning it over the side and place the screw to hold it in place.. |
|
15.-Insert the metal gaurd back on the lamp to keep the cables in place. |
|
|
16.-And secure it with its designated screw. |
|
17.-Finally place the metal cover at the side of the casing and place the screw to prevent it from moving. |
|
|
18.-No more than 15 minutes, and your done! |
IMPORTANT: After installing the replacement bulb, you should wipe it with a clean cloth to avoid any dirt or oil. Our hands are naturally oily…this could reduce considerably the life span of the new lamp.
Again, Discount-Merchant.com promises to be the low price leader in all Projection TV Lamps they carry…if this is not true, let us know and we’ll fix it!
Click below to buy this lamp now:
Lowest Prices Anywhere!