MITSUBISHI Lamp 915P027A10 How-To Replacement Guide

[Español]

For Part Number: MITSUBISHI DLP Lamp 915PO27A10, 915PO27010. (Unsealed replacement lamp for DLP, SMALL lamp with vents).

Lamp Type: DLP.

For Bulb: PHILIPS E22 UHP 132 / 150W 1.0 Lamp

E 22 1.0 Philips.

Click below to buy this lamp now:
buy now
Lowest Prices Anywhere!

Compatible TV Models: WD-62827, WD-62927, WD-73727, WD-73827, WD-73927.

NORMAL DISCLAIMER:
— Do NOT purchase generic brand lamps such as LTI, APO or third-party manufacturers such as OSRAM. These lamps were NOT engineered with and for your TV…only your Philips lamp has been engineered to work flawlessly and output the best possible color. Above that, it just doesn’t make sense to choose an aftermarket lamp for a $5-$10 difference (and in many cases they are more expensive!!).

Be a smart consumer and shop around, do your research! Discount-Merchant.com promises to be the low price leader in all Projection Lamps they carry…if this is not true, let us know and we’ll fix it!

Tools Required: 1 Standard Philips screwdriver, 1 Pair of Pliers, & A new lamp.

Time Required: About 15 minutes.

Abstract: This guide is being published to show how easy it is to replace your original MITSUBISHI 915P027A10 Lamp.

NOTE: We recommend you to use latex gloves when handling the new bulb to avoid any dirt or oil. Our hands are naturally oily…The oil residue from our hands can cause premature failure of the lamp if the front side of the lamp is not wiped down after the installation. It doesn’t hurt to do a final wipe with a clean, non-abrasive, lint-free cloth before reinstalling your lamp…

 

MITSUBISHI 915P027A10

MITSUBISHI 915P027A10

Lamp casing

 
BACK OF LAMP COVER

1.- First, locate two screws on the back of the lamp that are holding the lamp cover.

LAMP COVER

2.- Remove booth screws and take out the lamp cover.

 
PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

3.- Unscrew the nut in the top terminal of the lamp to disconnect the cable.

PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

4.- Using a Philips screwdriver disconnect the cable placed at the side of the lamp.

 
LAMP HOLDER & PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

5.- On the base of the lamp, there are three lamp holders.

LAMP HOLDER & PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

6.- Extract them to loosen up the bulb from the plastic enclosure.

 
LAMP CLIP & PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

7.- Uninstall the metal clip that holds the lamp in place.

PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

8.- Remove your old lamp, by pulling it out.

 
PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

A.- After removing your old bulb take out your new one, wich will look something like this.

PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

B.-Install your new PHILIPS E22 UHP 132/150W 1.0 Lamp lamp to the lamp holder.

 
LAMP CLIP & PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

C.-Reinstall the metal clip to the lamp, using the Phillips screwdriver.

LAMP HOLDER & PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

D.- Install again the three metal holders to the bottom of the lamp.

 
PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

E.- Reconnect the cable on the side of the lamp with the screw.

PHILIPS E22 UHP 132/150W 1.0 Lamp P-VIP

E.- Conjoin the cable to the top of the lamp by tightening the nut.

 
BACK OF LAMP COVER

F.- Place back the two screws to the back of the lamp cover.

MITSUBISHI 915P027A10

G.- And you’re finished,

Congratulations.

 

 

IMPORTANT: After installing the replacement bulb, you should wipe it with a clean cloth to avoid any dirt or oil. Our hands are naturally oily…this could reduce considerably the life span of the new lamp.

Again, Discount-Merchant.com promises to be the low price leader in all Projection TV Lamps they carry…if this is not true, let us know and we’ll fix it

 

Click below to buy this lamp now:
buynow
Lowest Prices Anywhere!

 

FixYourDLP.com Blog | FixYourDLP.com Forum | Guides
FixYourDLP Flickr | FixYourDLP YouTube

Copyright ©2014 FixYourDLP.com. All content on this website is intended for information purposes only. FixYourDLP.com is not responsible, nor liable for any damage caused by the end-user, faulty lamps or parts. Please, always have a service center or a trained service technician advise you before beginning any repairs on your own.